CCELL Go Stik 510 Battery

Screw a 510 thread cartridge onto the CCELL Go Stik 510 Battery, then inhale through the mouthpiece to fire it. The connection is a standard screw-on 510 thread, so hand-tighten the cartridge until it seats and stop there. Slide the switch on the body to 2.8V for flavor or 3.2V for stronger vapor. There is no button on the CCELL Go Stik 510 Battery, so your inhale is the only control you need.

The CCELL Go Stik 510 Battery has two settings on a slide switch, 2.8V and 3.2V. CCELL positions 2.8V as the flavor setting, running the cartridge cooler for a smoother draw, and 3.2V as the stronger setting for denser vapor. Move the switch before you inhale rather than mid-draw. Thicker or colder oil usually responds better to 3.2V on the CCELL Go Stik 510 Battery, while a fresh cartridge does well at 2.8V.

The CCELL Go Stik 510 Battery takes standard 510 thread cartridges of any size, including the larger formats that overhang slimmer stick batteries. Because the connection is a screw-on 510 thread rather than a proprietary pod fitting, cartridges from most brands work on it as long as they use the 510 standard. Check the thread on your cartridge before buying, since anything that is not 510 will not mount on the CCELL Go Stik 510 Battery.

No. The CCELL Go Stik 510 Battery uses a standard 510 thread with a screw-on design, so the cartridge threads directly into the battery and no magnetic adapter ring is involved. Nothing has to be pressed into the base of the cartridge first. If a listing describes the CCELL Go Stik 510 Battery as magnetic, it is describing a different device, because CCELL specifies a screw-on 510 connection for this one.

Charge the CCELL Go Stik 510 Battery through its USB-C port with the supplied cable and any standard USB power source, such as a phone charger or a computer port. Unscrew the cartridge first so the 510 contact stays clean and dry while charging. CCELL does not publish a charge time for the 280mAh cell, so unplug the CCELL Go Stik 510 Battery once charging finishes rather than leaving it connected overnight.

A CCELL Go Stik 510 Battery that will not fire is usually low on charge or not making contact with the cartridge. Charge it over USB-C first, then unscrew the cartridge, wipe the 510 contact on both parts, and screw it back on hand-tight without forcing it. Over-tightening presses the center pin down and breaks the circuit. If the cartridge itself is clogged, a slower and firmer draw at 3.2V often clears it.

Blinking on the CCELL Go Stik 510 Battery normally means the charge is low or the cartridge is not seated properly. Put it on USB-C charge and see whether the blinking stops. If it continues on a full cell, take the cartridge off, clean the threads and the center contact, and refit it hand-tight. A cartridge with a shorted or very low resistance coil can also make the CCELL Go Stik 510 Battery blink instead of firing.

Keep the 510 thread and the center contact clean, because residue from a leaking cartridge is the most common cause of weak or missed draws on the CCELL Go Stik 510 Battery. Wipe both with a dry cotton bud whenever you change cartridges. Store the device upright so oil does not seep into the connection, keep it away from heat and water, and charge the CCELL Go Stik 510 Battery on a hard surface rather than on fabric.

The CCELL Go Stik 510 Battery comes in six finishes: Electric Blue, Emerald Green, Lavender, Onyx Black, Sunrise Pine, and Sunset Blush. Every color choice is the same device inside, with the same 280mAh cell, the same 2.8V and 3.2V slide switch, and the same anti-slip matte body, so the finish is the only difference between them. Availability of each color can vary.